Lancia Motor Club Forum Banner
14 December, 2024, 08:30:45 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: 1 2 [3]   Go Down
  Print  
Author Topic: Project for sale - with an MGA engine?  (Read 17672 times)
0 Members and 1 Guest are viewing this topic.
Lojzik
Member
*
Posts: 6


« Reply #30 on: 10 February, 2021, 05:24:11 PM »

Thank you both for the photos, they are very useful.
Kari, may I ask you for the measure shown on the photo?


* 100_4537.png (782.14 KB, 800x533 - viewed 851 times.)
Logged
Kari
Senior Member
*****
Posts: 196


« Reply #31 on: 11 February, 2021, 08:58:35 AM »

The height of the crossmember is 90 mm. It extends and is welded to the diagonal U-profiles inside the boot.

Regards  Karl


* 100_4529.jpg (646.03 KB, 2304x1536 - viewed 347 times.)
Logged
Lojzik
Member
*
Posts: 6


« Reply #32 on: 15 February, 2023, 09:44:55 AM »

Hi everyone, I am still making progress with the rebuild of my Lancia, attached is a photo of the present state. I have a problem with the left rear wing which does not sit in properly whed aligned with the front wing and the running board. May I ask for the measurements as per the attached photos?


* IMG-20230213-WA0063.jpg (262.16 KB, 2000x1500 - viewed 192 times.)

* IMG-20230213-WA0075.jpg (399.84 KB, 1536x2048 - viewed 186 times.)

* IMG-20230213-WA0072.jpg (406.42 KB, 1536x2048 - viewed 185 times.)

* IMG-20230213-WA0069.jpg (354.39 KB, 1536x2048 - viewed 199 times.)
Logged
Kari
Senior Member
*****
Posts: 196


« Reply #33 on: 15 February, 2023, 05:07:27 PM »

Hi,
I can confirm measurements as follows:
Photo WA0069 = 920 mm
Photo WA0072 = 1190 mm
Photo WA0075 = 1290 mm

If you haven't done already, I suggest following: car on stands, draw a center line accurate on the floor length wise. Draw lines left and right parallel to the center line at a distance of 725 mm. This is the outline of the car. With the aid of a plumb line you can check symmetry and right angles of mudguards and running board.
I hope that helps.

I note that your rear axle is from a convertible. There is a spacer between the spring and the axle, the convertible sits a bit lower than the berlina.

Karl


* 100_4384.jpg (555.18 KB, 2304x1536 - viewed 214 times.)
Logged
Lojzik
Member
*
Posts: 6


« Reply #34 on: 16 February, 2023, 09:05:27 AM »

Hi Kari, thanks for the answer. You have confirmed the measurment on photo 0069 as 920 mm, but we have measured 820, may I ask you to check it again? Also may I ask for the dimensions between the rear spring hangers and the width of the rear wing as per the photos.


* IMG-20230213-WA0067.jpg (246.25 KB, 1536x2048 - viewed 185 times.)

* IMG-20230213-WA0064.jpg (526.74 KB, 1536x2048 - viewed 195 times.)
Logged
Kari
Senior Member
*****
Posts: 196


« Reply #35 on: 16 February, 2023, 05:16:20 PM »

I am sorry, its 820 mm.

Please find attached some data which could be of use. The distance between the springs is measured at the inside edges of the main blades.

Karl


* IMG_4109.JPG (501.1 KB, 1632x1224 - viewed 206 times.)

* IMG_4111.JPG (753.33 KB, 1632x1224 - viewed 190 times.)

* IMG_4113.JPG (680.39 KB, 1632x1224 - viewed 216 times.)

* IMG-20230213-WA0067.png (529.5 KB, 600x800 - viewed 473 times.)
Logged
Lojzik
Member
*
Posts: 6


« Reply #36 on: 18 February, 2023, 03:25:48 PM »

Thanks Kari, your advice is very helpfull
Logged
Pages: 1 2 [3]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.063 seconds with 21 queries.