simonandjuliet
Permanent resident
Posts: 2559
|
 |
« on: 22 November, 2022, 04:44:24 PM » |
|
I couldn't resist !
Latest addition to the fleet ..... very under appreciated little cars and consequently one of the most affordable sliding pillar Lancias. Needs re-commissioning because it has been in a collection/museum for many years
More later ..... need to finish a couple of others first
|
|
|
« Last Edit: 22 November, 2022, 07:53:34 PM by simonandjuliet »
|
Logged
|
AmilcarCGS, ApriliaCabrio,S2Aprilia, 2xArdea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20s4,R4 Sinpar, R4 Rodeo, 65 Moke, 3xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole,LR Defender, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan
|
|
|
simonandjuliet
Permanent resident
Posts: 2559
|
|
« Reply #1 on: 22 April, 2023, 03:13:20 PM » |
|
Just starting on this, so first job is to dismantle the brakes and replace all the seals and blow through the lines etc This car has been standing for may years so everything has dried up and was stuck
It came apart easily and all the seals and hoses have arrived from Italy
Couple of dismantling details. First photo shows the reservoir being taken apart. I use an induction heater to avoid damaging the body of the reservoir. If you are not careful you can tear the body from the mounting plate - very easy to do !
The heater gently cooks the old rubber seal and it comes undone by hand
Second, I have found the easiest way to remove the wheel cylinder pistons is to blow them out with the air gun. All I do before hand is remove any clud at the top of the piston. Once the first one is out , I push the other out with the press
I have shown an Aprilia shoe next to the Ardea shoes to show the difference in size
Finally, on the subject of Aprilia brakes, this is a shoe that I took from a friend's car - he was getting a strange noise from the front .....
It is a common problem, the pivot hole wears and the shoe leans out and scrapes the inside of the drum. If not dealt with they can do a lot of damage to the drum as well. This one has lost 5 or 6mm
Fortunately a new shoe has restored braking and stopped the horrible noise !
|
|
|
|
Logged
|
AmilcarCGS, ApriliaCabrio,S2Aprilia, 2xArdea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20s4,R4 Sinpar, R4 Rodeo, 65 Moke, 3xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole,LR Defender, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan
|
|
|
simonandjuliet
Permanent resident
Posts: 2559
|
|
« Reply #2 on: 12 May, 2023, 08:06:45 PM » |
|
All cleaned, honed and rebuilt and ready to fit, plus the tank has been rinsed and cleaned
We had the car running this week and it sounds lovely, so hopefully test drive next week once the brakes are back together and the tank refitted
Plus photo doing my day job ..... a Toselli 78 with rotovator (there is a video available !!)
|
|
|
|
Logged
|
AmilcarCGS, ApriliaCabrio,S2Aprilia, 2xArdea c'cino,S4 Ardea, Appia c'cino, Appia f'cino,B20s4,R4 Sinpar, R4 Rodeo, 65 Moke, 3xR60 Tractor, 2xToselli 78, Moto Guzzi Ercole,LR Defender, Mini ALL4 JCW, Moto Guzzi Cardellino, Fulvia GT, RE Himalayan
|
|
|
Richard Fridd
Permanent resident
Posts: 3490
|
|
« Reply #3 on: 13 May, 2023, 05:19:50 AM » |
|
Wonderful. What is the induction heater element made from?
Richard
|
|
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
|
Spider2
|
|
« Reply #4 on: 27 May, 2023, 02:18:58 PM » |
|
Lucky you like your coffee in reasonably tins or your bits and pieces storage system would be chaotic  |
|
|
|
|
Logged
|
|
|
|
|
