|
dhla40
|
 |
« on: 18 November, 2010, 05:47:13 PM » |
|
I am looking for a front wheel hub and RH front girling brake caliper for a S2 coupe.
Sean
|
|
|
|
|
Logged
|
1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
|
|
|
Richard Fridd
Permanent resident
Posts: 3496
|
|
« Reply #1 on: 18 November, 2010, 07:50:32 PM » |
|
hi Sean,i have a front wheel hub @ 15quid +p+p i think.please send delivery address if interested best regards richard[what is wrong with your existing one?]
|
|
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
|
dhla40
|
|
« Reply #2 on: 19 November, 2010, 09:17:55 AM » |
|
Hi Richard
My old one is slightly bent. at first I thought it was the brake disc but the runout measured on the hub is nearly .5 mm. The bearing feels ok so I am experimenting with shims between the hub and disc to try and correct it. If this fails then I will need another hub, I am near Southampton which end of the country are you?
Sean
|
|
|
|
|
Logged
|
1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
|
|
|
|
lancialulu
|
|
« Reply #3 on: 19 November, 2010, 10:12:57 AM » |
|
I cant se how this would bend before the disk as such a strong stub? Maybe the bearing needs looking at as I have found the the inner race can wear the stub and make the hub useless. It also shows the bearing is faulty but hard to see under nominal loadings such as manual inspection.
Tim
|
|
|
|
|
Logged
|
Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21. 12v
|
|
|
Richard Fridd
Permanent resident
Posts: 3496
|
|
« Reply #4 on: 19 November, 2010, 05:02:47 PM » |
|
hi Sean ,i am in west kent and work in london if that is of any use.i also have a set of four new bearings [just checked/regreased by my local lancia specialist]a brand new retaining ring and three front discs[secondhand].these are spares for my own cars but i can sell some things to pay towards my sedan project.best regards richard
|
|
|
|
|
Logged
|
Richard Nevison Fridd Happy Lancia, Happy Life
|
|
|
|
dhla40
|
|
« Reply #5 on: 19 November, 2010, 06:35:37 PM » |
|
With the hub fitted to the car and a dial gauge on the disc if I try to rock the disc there is less than .1mm movement but on rotation the runout is about .5mm. I have tried to find where the problem is by gauging the hub using a piece of glass as a surface plate, this is a bit hit and miss but seems to show the stub is about .2mm off centre. There is a slight step in the stub running surface which I thought was part of the machining but if this is meant to be smooth all the way across then this may be the problem.
Sean
|
|
|
|
|
Logged
|
1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
|
|
|
|
lancialulu
|
|
« Reply #6 on: 19 November, 2010, 07:19:00 PM » |
|
The step is your problem I am sure - esp if it is c.5-1cm width and at the inboard end. The stub should be parallel on its length.
Tim
|
|
|
|
|
Logged
|
Its not the winning but taking part! or is it taking apart?
Lancias:
1955 Aurelia B12
1967 Fulvia 1.3HFR
1972 Fulvia 1600HF
1972 Fulvia Sport 1600
1983 HPE VX
1988 Delta 1.6GTie
1998 Zeta 21. 12v
|
|
|
|
dhla40
|
|
« Reply #7 on: 19 November, 2010, 08:18:43 PM » |
|
Hi Richard
Have sent you a PM.
Sean
|
|
|
|
|
Logged
|
1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
|
|
|
|
thecolonel
Guest
|
|
« Reply #8 on: 19 November, 2010, 10:42:33 PM » |
|
Sean,
I've just sold my Fulvia c/with a load of spares there is a hub and front disc in the spares (Southampton)
I'm pretty sure the new owner will trade.
Geoff
|
|
|
|
|
Logged
|
|
|
|
|
dhla40
|
|
« Reply #9 on: 25 November, 2010, 05:17:53 PM » |
|
All sorted, thanks Richard for the hub and thanks Tim for the tip about the wear pattern.
Sean
|
|
|
|
|
Logged
|
1976 1.3s coupe
1973 1.3s coupe
1982 montecarlo project
1976 alfa GT
1981 alfa spider
|
|
|
|
