Lancia Motor Club Forum Banner
26 December, 2024, 04:22:23 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Need to contact the Forum Administrator? e-mail forum.admin@lanciamc.co.uk     -      Copy deadline for Viva Lancia is 12th of each month.      -      For Events e-mail events@lanciamc.co.uk      -      To Join the club go to http://www.lanciamc.co.uk/join.htm
 
   Home   Help Search Calendar Register  
Pages: [1]   Go Down
  Print  
Author Topic: Dutch Aurelia 3C  (Read 3931 times)
0 Members and 1 Guest are viewing this topic.
Jay
Megaposter
*
Posts: 440



« on: 01 April, 2014, 07:41:21 AM »

Not sure if this site has been mentioned before, I couldn’t find any references. I't's a Dutch Aurelia restoration, but the owner made his own 3C manifold designing and casting it from scratch.

Requires a lot of Google translating  

http://www.lanciaaurelia3c.nl/toch%20maar%203c.html
Logged

Julian Wood, Kingston, London
Charles T
Member
****
Posts: 52



« Reply #1 on: 02 April, 2014, 09:04:16 PM »



I have seen this page from the same author in English:
http://lanciaaurelia3c.nl/3C-GB-WhyNot3C%202.pdf

You may also be able to get back to the English version of this website but I could not find it.
Logged
GG
Megaposter
*
Posts: 572



WWW
« Reply #2 on: 03 April, 2014, 12:14:54 PM »

Saw this setup at Sliding Pillar 2013, done with Martin Willems help.

Francosport also goes by the name of Classic Lancias, very passionate about his Aurelias, and has been involved in fabrication of a number of SS parts (bumpers, brake parts).


* _DSC1371 copy.JPG (573.05 KB, 1800x1200 - viewed 494 times.)

* _DSC1372 copy.JPG (598.05 KB, 1800x1200 - viewed 464 times.)
Logged

Appia C10, Flavia 2000 coupe, Fulvia Fanalone
chriswgawne
Permanent resident
**
Posts: 2091



« Reply #3 on: 03 April, 2014, 02:26:55 PM »

IMHO the triple carb set ups (and the twin carbs as well but to a lesser extent) for Aurelias look lovely as they definitely fill an empty space but they seem to be of limited value for any car which the owner intends driving only on the road.
A re-jetted single Weber 40DCL/Z with opened out chokes sitting on a well built carefully run in engine is perfectly satisfactory.
Having said that I have twin Webers on my race car and also the B20 we have owned since 1978 but slow running can be a problem due to worn butterfly shafts and also the jets need to be reduced to avoid over fuelling.
Twin Weber 36's are a much better bet for the 2.5l engine.
Chris
Logged

Chris Gawne
Mobile: 07778 216552
Charles T
Member
****
Posts: 52



« Reply #4 on: 28 April, 2014, 07:40:13 PM »

Chris,

I read you comments on carburettor set up with interest.
I have also been having problems with the idle phase and have not yet got to the bottom of it, the principle problem being with stalling from standing or slow running.  This is with a pair of 40DCZ's on a 2.5L engine (S6).

I assume that 36DCZ carburettors are not easy to obtain, and then would need some adjustment to fit and also tune.
Would it really make enough difference to the usability of the car to make the whole exercise worthwhile, given the probable expense involved?
In my case, I am not likely to be doing any racing and I have not been able to make a direct comparison with another similar car.

Charles
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Contact the Forum Administrator

LMC Forum copyright © 2007 - 2021 Lancia Motor Club Ltd

Powered by SMF 1.1.20 | SMF © 2006-2011, Simple Machines
Page created in 0.066 seconds with 20 queries.